Flushing Oil Concentrateā¢
Flushing Oil Concentrate restores pristine cleanliness to the dirtiest of both diesel and gasoline internal components, and has saved thousands of engines from expensive rebuilds.
- Eliminate engine sludge & hard carbon
- Release stuck piston rings
- Reduce smoke, blowby & oil use
- Restore cylinder compression
- Stop diesel engine oil going black right after an oil change
- Use in all engines, transmissions & diffs
- Detergent based – no corrosive or abrasive solvents
Flushing Oil Concentrate is a remarkable product, and is possibly the most effective treatment in removing harmful and performance draining sludge, hard carbon and other contaminants and deposits from oil-wetted engine components. Not only does it restore full cleanliness to the entire crankcase, removing all engine sludge, but it also frees up stuck piston rings, restoring compression and oil control and reducing blow-by.
Use it now before it’s too late! Restore your engine to like new cleanliness and performance. Use it at time of engine oil change.
Flushing Oil Concentrate
Flushing Oil Concentrate removes engine sludge and hard carbon deposits
Lubricating oil has 2 often-overlooked, yet very important functional requirements – It has to COOL and it has to CLEAN the components it is in contact with. Full, unrestricted flow of clean oil to all parts is essential to provide proper cooling and lubricating ability to the engine. Amazingly, this duty is almost universally ignored by mechanics investigating over-heating and/or oil pressure issues in engines, be it diesel or gasoline.
Contaminated Oil Destroys Engines FAST
The problem is that contaminants suspended in oil act as an abrasive, like a grinding paste, but on a smaller scale. Between two sliding surfaces (e.g. piston ring and cylinder bore, or bearing and journal), the presence of suspended contaminants can create abrasive wear. The more contaminants, the greater the potential for accelerated wear. Always make a mental note of the oilās degree of discoloration. The darker it is, the more contaminants it holds, and the less its ability to protect your engine and the greater likelihood of premature failure.
Most Effective Treatment To Remove Destructive Sludge
Prevent engine-destroying sludge like this – Use Flushing Oil Concentrate at every oil change
The fastest and most cost effective solution to this potentially disastrous problem is to use Flushing Oil Concentrate at the recommended treatment rate. Flushing Oil Concentrate is added to the oil at the time of the oil change to safely dissolve deposits and suspend sludge. It will thoroughly revitalize a heavily sludged engine. Flushing Oil Concentrate contains a highly concentrated selection of detergents and dispersants (not solvents that can cause problems with oil seals, O-rings, even bearings etc.) which enable lubricating oils to dissolve and suspend deposits as a very fine diffusion. In such a way, sludge, gum, dirt and wear metals are removed with the oil change.
Flushing Oil Concentrate is the most effective treatment in removing harmful and performance draining sludge, hard carbon and other contaminants and deposits from oil-wetted engine components. Not only does it restore full cleanliness to the entire crankcase, removing all engine sludge, but it also frees up stuck piston rings, restoring compression and oil control and reducing engine blow-by. Give your engine every chance of a long and serviceable life.
How to use Flushing Oil Concentrate to get the very best result
Detailed Treatment Instruction Sheet: Initial concentrated treatmentĀ – Bring engine to FULL operating temperature. Drain old oil and refill with new, clean oil (this can be inexpensive oil for this purpose as it will only be in the engine for approximately 45 minutes). It is a good idea to replace the oil filter/s at this time as possible heavy contamination of the existing filter may occur during the flushing process. Operate the engine to warm up the oil again, then add Flushing Oil Concentrate to engine oil at 0.5 fl oz per quart (12.5 mL per liter) of engine oil. Run the engine at a fast idle, stationary, for 45 minutes. For most small and medium size engines, this means 1500-2000 RPM. For larger size engines (e.g. over 9.0-Liter/550 cubic inch engine displacement), run at about 1200 RPM. Stop the engine and drain the engine oil while it is still hot and replace oil filter/s. Refill with new, quality engine oil.
Continuing maintenance – Bring engine to FULL operating temperature. Add Flushing Oil Concentrate to the existing engine oil at 0.1 fl oz per quart (2.5 mL per liter) of engine oil. Drive/operate normally for 30 – 60 minutes, then continue with normal oil change while oil is still hot. Click here for more details.
Maxodyne AW10 Antiwear – formulated to deliver tremendous increases in lubricant load carrying ability, wear reduction and friction/heat reduction
Don’t forget – after using Flushing Oil Concentrate to get the entire lubricating system totally clean, add AW10 Antiwear to the new oil to give extra strength to the oil, and reduce component wear and premature oil breakdown and degradation. Significantly extend the long term reliability of your engine, and reduce operational costs!
Choose the most appropriate Flushing Oil Concentrate size for your particular need. Various size options are available –
Flushing Oil Concentrate is added directly to the oil immediately prior to the oil change. It is not recommended to be added to the oil and ran for extended periods of time.
Basically, the initial, hard-working, concentrated flush breaks down and suspends heavy, baked-on sludge – the sludge that causes piston oil-rings to block up and stick in the grooves, oil pumps to reduce pressure, and oil galleries to be restricted.Ā It also dissolves the clumps of hardened sludge on the oil pan and other crankcase components. It assists in the breakdown of hard carbon on the piston skirts, lower compression ring and cylinder walls.
For the very best results, we recommend the following treatment rates –
Initial/Dirty Engine concentrated flush: add Flushing Oil Concentrate to the engine oil at 0.5 fl oz per quart of engine oil (12.5 mL per liter of engine oil).
- 8 fl oz of Flushing Oil Concentrate treats a maximum of 16 quarts (4 gallons/19 liters) of oil
- 16 fl oz of Flushing Oil Concentrate treats a maximum of 32 quarts (8 gallons/38 liters) of oil
- 32 fl oz of Flushing Oil Concentrate treats a maximum of 64 quarts (16 gallons/76 liters) of oil
- 64 fl oz of Flushing Oil Concentrate treats a maximum of 128 quarts (32 gallons/151 liters) of oil
- 1 Gallon of Flushing Oil Concentrate treats a maximum of 256 quarts (64 gallons/302 liters) of oil
Continuing maintenance oil change flush: add Flushing Oil Concentrate to the engine oil at 1/10th fluid ounce per quart of engine oil (2.5 mL per liter of engine oil).
Instructions:
INITIAL TREATMENT/DIRTY ENGINES
Bring engine to FULL operating temperature. Drain old oil and refill with new, clean oil (this can be inexpensive oil for this purpose). It is a good idea to replace the oil filter/s at this time as possible heavy contamination of the existing filter may occur during the flushing process. Operate the engine to warm up the oil again, then add Flushing Oil Concentrate to engine oil at 0.5 fl oz per quart (12.5 mL per liter) of engine oil. Run the engine at a fast idle, stationary, for 45 minutes. For most small and medium type engines, this means 1500-2000 RPM. For larger truck type engines (e.g. Series 60 Detroits, Cats, Macks, Cummins, etc), run at about 1200 RPM. Drain the engine oil and replace oil filter/s. Refill with quality engine oil. Detailed instruction here.
Example:
- 5 quart/liter oil capacity = 2.5 fl oz (60 mL) Flushing Oil Concentrate
- 5 gallon (20 liter) oil capacity = 10 fl oz (250 mL) Flushing Oil Concentrate
- 10 gallon (40 liter) oil capacity = 20 fl oz (500 mL) Flushing Oil Concentrate
CONTINUING MAINTENANCE
Bring engine to FULL operating temperature. Add Flushing Oil Concentrate to existing engine oil at 0.1 fl oz per quart Ā (2.5 mL per liter) of engine oil. Drive/operate normally for 30 – 60 minutes, then continue with normal oil change while oil is still hot.
Example:
- 5 quart/liter oil capacity = 0.5 fl oz (12.5 mL) Flushing Oil Concentrate
- 5 gallon (20 liter) oil capacity = 2 fl oz (50 mL) Flushing Oil Concentrate
- 10 gallon (40 liter) oil capacity = 4 fl oz (100 mL) Flushing Oil Concentrate
Occasionally, on an engine with years or decades of sludge build up, a second follow up concentrated flush may be required soon after the initial flush (600 – 1200 miles, 1000 – 2000km). It is suggested to add Flushing Oil Concentrate to clean oil (as per instructions for the “Initial Treatment/Dirty Engines”), at a rate of 0.25 (1/4) fl oz Flushing Oil Concentrate per quart of engine oil (6.25 mL per liter of engine oil). Operate the engine normally for between 4 – 6 hours, then drain the oil while hot, replace oil filters, and fill with quality oil.
(32 fl oz = 946 mL, 1 liter = 33.8 fl oz)
No Interest!Ā No Fees!*Ā So Easy!
With Klarna you can pay in 4 interest-free installments over 6 weeks.
Split the cost of your purchase into 4 equal payments over 6 weeks that are automatically charged to your card every 2 weeks.
How it works
- Use your own valid debit or credit card to pay (no prepaid cards).
- The initial installment is charged when we complete your order (this is usually the shipping date).
- One of the remaining installments is automatically charged to your card every 14 days after your first payment.
- There are no interest charges with Pay in 4 installments, and no fees* when you follow your automatic payment schedule.
What to do –
At Checkout
- As usual, enter your card billing address, your contact telephone number, and email address, and a shipping address if it is different from your billing address. You will need a valid phone number that can receive text messages as Klarna will text you a security code which you must enter to complete the transaction.
- Choose Yes or No for Unattended Delivery Authority.
- Select the option “Buy now, pay later”
- Click the “I have read and agree to the website Store Policy“ check box.
- Click Place Order.
- Follow the instructions provided.
- Click on Text me the code.
- Enter the code you receive.
- You may be asked to confirm your identity by entering your birth date etc.
- Then just submit the order. Done! It’s that easy!
- We will pack and ship your order within 1 business day (we try to ship the same business day).
When the order is shipped
After we confirm that the order is on its way, Klarna will charge your card for the first installment amount. Klarna will send you a notification once the payment has been processed.
Every 2 weeks
Every 14 days Klarna will automatically charge your card one of the remaining installments until the full order amount has been paid. You will be informed ahead of time.
*No fees when you pay on time
Do I pay Sales Tax on my order?
U.S. orders: When ordered directly from maxodyne.com website or phone-in order –
No Sales Tax is payable on orders with a Delivery Address outside of Utah.
Orders with a Delivery Address within Utah are currently subject to a Sales & Use Tax charge of 7.45% of the product price, i.e. Product cost = $100, Sales & Use Tax = $7.45.
Sales & Use Tax charges are automatically calculated and applied at the point of Checkout.
Shipping charges, if any, are not subject to Sales Tax.
International orders: When ordered directly from maxodyne.com website or phone-in order –
No U.S. Sales Tax charge applies to orders with a Delivery Address outside of the U.S.A.
There may be Duties and/or Fees applied to your order by your destination country’s Customs and Import Authority. These fees, as calculated by the local Customs Authority, are payable by the Purchaser/Importer at the time of Customs Entry.
USA Lower 48 States – From our facility in Utah, we ship daily using FedEx Standard Express as our main shipping contractor. Orders are shipped within 1 business day of receipt, and delivery is within 3 business days*. Shipping is free within the lower 48 States for orders over $50.^Ė
Please note, FedEx will not deliver to USPS P.O. Box numbers as per USPS guidelines. Please provide a physical street address for shipping/delivery.
Alaska, Hawaii and Canada – we ship to Alaska, Hawaii and Canada at a subsidized rate. Shipping rates are added automatically at Checkout. All prices are in U.S. Dollars. GST & Duties/Fees may apply to Canadian purchases, payable by the purchaser as calculated by CBSA at time of entry.
Canadian customers – if it helps, we can also ship to any USA destination (Lower 48 States) for local pick-up or on-forwarding by a carrier of your choice; for example, you may have your own preferred carrier from the USA to Canada. Free shipping applies to destinations within the Lower 48 States. Ask us for details.
International Orders – We welcome our International customers! Please Contact Us for a shipping cost quote and further instructions about completing your purchase.
Please note – due to certain logistics and Federal Regulations, we are unable to ship to some Countries/Territories.
Need your product in a hurry?! Utilizing the services of FedEx and UPS, we can priority ship your product to your chosen destination*. Just contact us, tell us where you need it and when ā we can then calculate the cost and advise you of the shipping details. All prices are in U.S. Dollars.
*We reserve the right to use other shipping suppliers and services as we deem necessary from time to time, depending on prevailing circumstances. Delivery schedules may be affected by conditions beyond our control.
^A $10 shipping charge applies for orders below $50 excluding tax.
ĖApplies to retail quantities only. For commercial quantities, please contact us for further details.
Cummins ISX
“Tell ya what! After using theĀ Flushing Oil ConcentrateĀ the way you recommended,Ā the engine oil is still as clean as new after about 600 miles! I’ve noticed too that the engine seems to be smoother and up on power – probably theĀ FTC DecarbonizerĀ doing it’s thing! (2012 Cummins ISX). I’ll keep in touch.”
Marvin M, Lewistown, IL
Chevrolet Cruze Diesel engine oil
“Just thought I’d send you a picture of the dipstick approximately 700 miles after we did the engine oil flush with the Flushing Oil Concentrate. The oil is still so clean I can hardly see it on the dipstick. I am still amazed at how well it cleaned out the sludge and other muck in my 2010 Chevrolet Cruze Diesel. I’d never thought diesel oil could be so clean. Amazing result. Many thanks.”
Brian M, Logan, UT
Duramax problems solved
“My 2008 Chevrolet Duramax, with only 129,000 miles, was running badly and intermittently blowing clouds of black smoke at highway speeds. It had bad power loss above 65 mph – usually no throttle response above this speed. Also, it felt and sounded like the turbo was constantly surging at any speed. Over the last couple months I’ve been usingĀ FTC DecarbonizerĀ andĀ ULS Diesel EnhancerĀ in the diesel, and it has made aĀ tremendousĀ difference! No black smoke! Running so much smoother, full power again, and I’m getting 2.5 mpg better fuel mileage! I’m looking forward to the results I get from theĀ Flushing Oil Concentrate. Great products that do as you said they would. Really appreciate your help.”
Ryan D, Lawrenceburg, TN
5.9 Cummins oil consumption solved
“Just a note to say the truck (5.9 Cummins) is running much better and smoother. The oil is still normal and clean after 600-plus miles, oil consumption is much lower now as well, and fuel eco is up. TheĀ Blow-by Pack has worked as you said it would. Thanks!”
Marc M, Chico, CA
Cleaner & Cooler Cummins
“I used the Flushing Oil Concentrate in my 1997 Dodge Ram Cummins. Amazing result! The oil on the dipstick stayed really clean – never seen that before. And it runs a lot cooler now, especially when towing the 5th wheel. Many thanks!”
Dana Z, Santaquin, UT
Freightliner fix
“I’ve been using the FTC Decarbonizer in my Freightliner N14 for a few months now. As you know I was a little wary about trying it, but the information you gave me convinced me to give it a shot. It’s made a tremendous improvement! Blow-by has decreased from 6 inches down to 1 inch, exhaust smoke has died down considerably, fuel mileage has gone from 5MPG to close to 6MPG (20% increase), the engine stutter between gear changes has disappeared completely, the high temperature problem it had at idle is totally fixed, the engine starts so much better now than before, the engine is running so much smoother and better – it’s doing everything it’s supposed to! I did the engine oil flush with Flushing Oil ConcentrateĀ over this past weekend. Seriously, I was amazed at the huge amount of sludge and carbon that came out, all in just one stroke! I’ve driven for a few days now, and checked the dipstick – it looks BRAND NEW, it’s cleaner than ever! The cheap products I’ve tried before did absolutely nothing. Your products have done exactly what you said they would. Engine Blow-by Pack, hell of a product! I strongly recommend it to anyone. It’s worth every cent.”
Howard B, Toledo, OH
2012 Kenworth W900
“I run a 2012 Kenworth W900, with around 340,000 miles on it. My buddies lately have been getting hit with massive repair bills on their trucks – it has crippled some of them. They’ve been telling me I’m gonna be next as my truck is at the mileage when things start to go bad. I do not want to be in that situation. I believe it’s better to spend affordable dollars now on preventative maintenance, than unaffordable dollars later as a result of major component failure. So I’m using the Engine Blowby Pack – FTC Decarbonizer and Flushing Oil Concentrate.”
Dusty R, AZ
Noticeably less smoke
“I did theĀ oil flush with great results as far as noticeable sludge. While not 100% free of sludge (oil now has slight dark grey tinge, but does not stain fingers when rubbing together), but the difference before and after is really striking, great product! The performance and lowering amount of smoke at start up are noticeable & engine seems quieter.
Other thanĀ sludgy oil, my main concern was a bit of blue haze I’m getting driving up grades when the engine is under load. I believe I am burning a bit of oil, not noticeable on the dipstick level or anything, but that blue haze is a tell-tale sign. After the flush, the blue haze was only just noticeable, but I think it may be as I drive more, it’s possibly improving (Cleanpower working?) I am not even half way through my first tank of fuel, as I haven’t been driving tons.
Yes I do want theĀ FTC Decarbonizer!”
Christian K, Oakland, CA
Would never have believed this
“200,000 miles on the build, this engine puts out 650 hp and 1650 lb/ft of torque, the dipstick is after one treatment of your Flushing Oil (Concentrate) treatment product. I thought I was rolling the dice when I got your products and would never have believed this. There it is right there, in the picture, the dipstick after it was run up and warmed and driven for about 10 miles. Can’t wait to see what the rest of the product FTC Decarbonizer will do for my truck as well as the fleet of equipment that I take care of. I’m sure we will be a customer for many years to come. I manage a fleet of equipment here in Colorado. I took the dipstick down and showed it to the owner because, well, you just have to see it to believe it.”
Phil P, CO
Freightliner FTC Decarbonizer Fix
“Thought I’d let you know how the FTC Decarbonizer worked with the Freightliner. It has 2 million miles and never had a rebuild, but starting to have blowby. I added the FTC Decarbonizer that you sent me, and am amazed at how it worked. The blowby came to a screeching halt, fuel mileage went from 5.4 to almost 7, and within the first 100 miles it was running a lot smoother, and could really feel more power. It really blew me away. My driver loves it! I’ll be telling my buddies about it, for sure! Send me some more, and add some Flushing Oil Concentrate to my order as well. Very impressed.”
Bill P, Sharon Springs, NY
Extreme Tractor Blow-by Fixed
“I had a drastic blow by problem with my tractor and was using 2-3 quarts of oil per week without driving it more than 1 hr per day.Ā I talked to 3 different mechanics and they all said that an overhaul was the only solution and it would cost at least $5000. After talking to the Maxodyne Team I felt assured that it was worth a shot to try out the FTC Decarbonizer and the Flushing Oil Concentrate. I did and was amazed at how fast it worked! I did the oil flush as recommended and also put the Decarbonizer in the fuel tank. I drove it the same as before and I didn’t need to add any oil for the first 3 weeks, then I added 1/2 quart.Ā I went another 3 weeks and added another 1/2 quart…Ā the blow by virtually stopped from then on, I’ve only added a little oil now and again when I remember to check it.Ā I started the process in January and it is now the end of May and I have added approximately 3 quarts total in 5 months and don’t expect to have to add much at all as long as I keep using the Decarbonizer each time I add fuel. This is amazing to me!Ā I didn’t expect it to be such a drastic change. This is saving me $5000 plus the downtime it would have taken to overhaul the motor.Ā I own a horse arena and I need to groom it every day so to be without it for 2-3 weeks was a nightmare for me.Ā That’s why I started looking for another solution. I’m sold!”
Bruce W, Carthage, MO
Thanks for your help
“The well-packaged shipment from you arrived this morning – fast delivery!
My slip neighbour and I both greatly appreciate your response and help with this matter – a class operation.
I will help M… with his oil flush and weāll start the Decarbonizer treatment.
Many thanks!”
Douglas C, Victoria, BC, Canada
Saved an engine overhaul
“I want to thank you for putting out a product I can truly say has saved me money. I repair and sell Grasshopper lawn mowers and love their Kubota Diesels and have had a few of them that have not been taken care of. But instead of having to tear them down and rebuild them, I added the FTC Decarbonizer and the Flushing Oil Concentrate, and was blown away with the results of my first application. Before I put the additives in the one mower I truly thought I was going to have to take apart. I ran it for a month and during that time, I noticed less and less blow-by and it had the power to cut thick thatch with no problem. I just wanted to let you know what good products you have.”
Rich M, Swansea, IL
Preventative maintenance, great results
āI started using the products about 6 years ago when I needed to rejuvenate a Yanmar turbo 4-cylinder engine on a newly purchase 27 year old sailboat. The engine was in very poor condition ā theĀ exhaust smoke was black, and it had little torque.Ā As itās a marine engine with little chance of working āhardā, it did take quite a while of using theĀ FTC DecarbonizerĀ andĀ Cleanpower, along withĀ 3 oil flushes over time usingĀ Flushing Oil ConcentrateĀ to get the engine back to as new condition. As you know, the turbo was mechanically damaged, so I replaced it.
Seeing the wonders these product can provide I started using them on my two V6 Mercedes diesel-engined vehicles. These are late model vehicles withĀ diesel particulate filtersĀ and exhaust fuel treatment additive (DEF).
I bought both of these vehicles, used, with low kilometers. I now have 110,000 kilometers on one car, and the SUV has reached 160,000 kilometers. Both engines run withĀ FTC DecarbonizerĀ andĀ ULS Diesel Enhancer. When I change the oil, I use theĀ Flushing Oil ConcentrateĀ as you recommend. I always use high quality full synthetic oil in these engines.
I can see that the engine oil is soot/carbon free, andĀ the oil remains clean and honey coloredĀ for a period of time.
Result is my carsĀ perform superblyĀ with unbelievable acceleration (for a diesel) and are very economical on fuel.
So for me these products are preventive maintenance and I know it is not a scam with the results I get.ā
Jacques L, Quebec, Canada
Remarkable improvement
“I do not have enough good to say about these products!!
I own a 2002 Peugeot 308 with a 2.0 turbo diesel. (mileage: 290K kilometers/180k miles)
When I purchased this vehicle it was at 150k (93K miles) and felt under-powered due to the mileage.
I contacted Maxodyne and spoke with Scott, and asked if he felt their products could help my small diesel car. After asking me some questions about the car, he suggested I use 3 products. I used the oil flushing treatment, and I have since been running the FTC Decarbonizer and the ULS Diesel Enhancer in every tank.
Scott is extremely knowledgeable and helpful when it came to helping me sort my concerns and needs with this little diesel. (Do not hesitate to contact him, he is a joy to work with.)
Frankly, I am still in awe of the vast difference in the throttle response and power difference while driving this little car, even after the first two treatments.
When I first purchased this vehicle, before the treatments, I was getting an average of 950km per 55L tank of fuel (5.7L/100km, or 41MPG). Since treating the engine with these products I have been getting 1150-1200km (4.6L/100km, or 51MPG) from the same tank. Almost a 25% increase in fuel economy!!
These products pay for themselves every time I need to go to the pump.
I am a firm believer in these products, and will be using them in all my diesel vehicles from now on.”
Brian M. Queensland, Australia
Amazing stuff
“I want to let you know, this stuff is amazing! I bought an old Dodge Ram with the 5.9 Cummins engine, about 200,000 miles on the clock. It was veryĀ low on power, clouds of exhaust smoke, and hadĀ lots of blow-by. I got theĀ FTC DecarbonizerĀ from you and added it to the fuel. Seriously, within about 2 hours of driving, I could tell theĀ power had improved noticeably,Ā and theĀ blow-by had reduced significantly. I was shocked at how well it worked! Now Iāve done about 1500 miles, and the exhaust smoke has completely disappeared, and itās running much smoother! Iām getting theĀ Flushing Oil ConcentrateĀ from you now to finish the job right.”
William M, Menifee, CA
Really exceeded my expectations
āThe products (Flushing Oil ConcentrateĀ &Ā FTC Decarbonizer) worked great, really exceeded my expectations. Hopefully the longer they run, the better they will get. I just placed another order today for one of my hotshot drivers. Thanks for everything.ā
David L, Tyler, TX
Chevy Astro low oil pressure
āOur old, yet mostly reliable 1997 Astro van has had a progressively worsening
low oil pressure problemĀ for a long time. At idle, oil pressure sat around 30psi,Ā and at higher RPM, it could only manage just over 40psi. Highly recommended by a friend, I did the engine flush withĀ Flushing Oil Concentrate. The very first start with new oil, and immediately the oil pressure at idle was 55psi. At highway RPM it now sits solidly on 60psi. I couldnāt be happier with the result! Awesome product, awesome result. Thanks.ā
Nathan A, San Francisco, CA
Detroit 60 Series Blow-by fix
āMy Series 60 Detroit developed an oil use andĀ blowby problemĀ at 500,000kms (310,000 miles) after an in-chassis rebuild. Running yourĀ Flushing Oil ConcentrateĀ (in combination withĀ FTC Decarbonizer) tightened up the blowby and oil burning. Iāve continued to use these products and 6-7 years later, the truck is still going great.ā
Phil Riseley, Riseleyās Bulk Haulage, Australia
Black smoke and blowby Cummins 5.9
“We got theĀ Blowby PackĀ to see if it would help our 2003 Dodge Cummins 5.9 24 valve engine. Itās got 300,000 miles on it and itās been havingĀ some pretty bad blowby happening, as well as a lot of black exhaust smoke. We usedĀ theĀ oil flushĀ treatment, and have been running theĀ FTC DecarbonizerĀ in the fuel. Weāve only doneĀ just over 100 miles and already weāre seeing an improvement. The black exhaust smoke has completely stopped, itās running so much smoother, power feels to be up from before, and the blowby seems to be starting to slow down. I think that may take a bit more time yet. I honestly thought the engine was in really bad shape and was heading for a full rebuild ā $8000.Ā Weāre really happy with the results. These products seem to be doing as you say they will. Weāll get some more soon for our daughterās 2003 Ford Powermax. Thanks, a great product.”
Arnold H. Lubbock, TX
Detroit 60 Series Blow-by fix
āMy Series 60 Detroit developed an oil use andĀ blowby problemĀ at 500,000kms (310,000 miles) after an in-chassis rebuild. Running yourĀ Flushing Oil ConcentrateĀ (in combination withĀ FTC Decarbonizer) tightened up the blowby and oil burning. Iāve continued to use these products and 6-7 years later, the truck is still going great.ā
Phil Riseley, Riseleyās Bulk Haulage, Australia
Cummins ISX Burning Oil
“My Peterbilt 389 with the ISX-15 wasĀ burning tons of oil and had bad blowby. Itās got around 500,000 miles on it. I was going through about 3 gallons of oil every 1400 miles. So I started using theĀ FTC DecarbonizerĀ I got from you, hoping I wouldnāt have to get a rebuild. Within about a monthĀ the blowby had slowed down a lot!Ā And theĀ oil burning is right down too, now I only need to take 1 gallon of oil with me instead of 3 or 4 gallons. Iām confident that will improve more as I keep using theĀ FTC Decarbonizer. Iāll use theĀ Flushing Oil ConcentrateĀ in about 3,000 miles when the oil change is due. Hoping thatāll tidy up the last of the oil burning. Thanks for your help.”
Steve B. San Diego, CA
Duramax Blowby
“My 2003 Silverado Duramax had lots of blowby. Itās only got 242,000 miles, mostly pulling a 5th wheeler around, power was still good. I got yourĀ Blowby PackĀ and got the oil flush done. Before using theĀ Flushing Oil ConcentrateĀ when I was stopped at traffic lights, I could see blowby coming out each side of the truck. Now within a couple days the blowby has reduced by about a half, definitely a lot less blowby smoke, Iāve got to get down and look under the truck to see, and now thereās only a little bit coming out. I think the more I drive it now using theĀ FTC DecarbonizerĀ in the fuel will probably fix the last of the blowby. Good products.”
Bert G, Bellingham, WA
Corvette Blowby
“A friend bought this 1991 Corvette recently. Itās only got 139,000 miles on it, but it obviously had a bad maintenance history. It was still running great though and had good power, but the engine blowby was very bad. The pressure in the crankcase was enough to blow the dipstick out and oil was literally pumping from the tube. We did a leak down test and every cylinder had 20% or more drop. I followed theĀ directionsĀ for using theĀ Flushing Oil Concentrate, the oil came out looking very brown for brand new oil. The blowby pressure reduced a significant amount, the dipstick didnāt budge at all, and when I take the dipstick out now, thereās only a small amount of pressure there. The amazing thing was I did another leak down test immediately after the flush, and now itās around 10% ā 12%. Weāre going to get theĀ FTC DecarbonizerĀ in the gas tank now and expect to see the blowby decrease even further as the rings and cylinders clean up. Very happy with the result!”
Dave D, Belleville, MI
Difference was like Night & Day!
“TheĀ Engine Blowby PackĀ worked as it was supposed to. The Cummins ISL 425 in our motorhome had developedĀ bad blowby, and so much oil spray coming from the blowby tubeĀ it was covering the tow car with oil. The dealer checked and told us that it showed 50% idling hours during itās life so far. We flushed the oil the way you said with theĀ Flushing Oil Concentrate, and started using theĀ FTC DecarbonizerĀ in the diesel. ItĀ started to get better quickly, and now weāve run 700 gallons of diesel through it andĀ the blowby is completely gone! TheĀ difference was like night and day!Ā An excellent result. We were skeptical to begin with, having been told that the only way to fix the problem was to overhaul the engine. WeĀ couldnāt be happierĀ with the results. WeāllĀ keep using the products to keep it running so good. Many thanks.”
Patrick T, NE
Really great result
“My Cummins 5.9 hadĀ bad blowby and some heavy exhaust smoke.Ā Annual emissions test was due, and I was sure it wouldnāt pass the way it was. It doesnāt have high mileage, but I knew it had not had enough oil changes during itās life. I took my chances and got theĀ Blowby PackĀ from you and did theĀ oil flushĀ first.Ā The oil that came out looked horrible. I started using theĀ DecarbonizerĀ andĀ within a week or two it had settled down, it passed emissions easily. A really good result!Ā Hereās something interesting, I had left the old oil in a drain bucket under cover forĀ few weeks before getting rid of it. When I looked at it just before I got rid of it, it looked like black pitch paint ā so thick and almost sticky. Thatās what came out of the engine!Ā The dipstick still shows clean oil even now.Ā Very pleased with the result.”
Greg M. Boston, MA
Cummins ISX Blowby Eliminated
“The ISX had 200,000 miles on a rebuild andĀ the blowby was bad, blowing oil out the tube. I got theĀ Blowby PackĀ off you and started using theĀ FTC DecarbonizerĀ right away. Bit by bit I could see an improvement. I had to wait for a bit to do theĀ oil flushĀ because Iād only just changed the oil, but I did the flush at the next oil change.Ā I noticed the blowby kept getting better, and now I have to say itās eliminated. The engine is running very good too. The idea of getting your product was toĀ avoid a rebuild, and it worked! IāmĀ getting more of the products just to keep it clean and running strong.”
Ralph N, Houston, TX
Detroit Series 60 revived
“My Series 60 had an inframe rebuild 300,000 miles ago, and blowby was starting to show up and it was starting to use oil. I tried someĀ big name, off-the-shelf oil additivesĀ to try to stop the problem, but that didnāt help none. I found theĀ Engine Blowby PackĀ online and gave it a shot. Followed theĀ oil flushĀ directions, and nowĀ the engine oil is still clean on the dipstick. That did a great job. Iāve been using theĀ FTC DecarbonizerĀ in the diesel, and Iāve only gone through about 250 gallons of diesel and already I can see an improvement.Ā I could see the blowby in my lights at night, it looked like fog when I was parked up.Ā Now I can hardly see it at all. Great improvement, I can see itās working. Very happy with the result. Iāll get more when I finish what I ordered,Ā just to keep her clean and running well.”
Ben G, TX
Love the products!
“Love your product and excellent service! Thanks. (Marine Diesel StabilizerĀ andĀ Flushing Oil Concentrate, 2015 Ocean Yacht, twin 57HP Yanmar diesel engines.)”
Ren G. Edgewater, MD
No problems in 3 years
“Iāve been using your products for coming up 3 years, andĀ Iām amazed at how strong my Freightliner still is.Ā It just keeps running with no problems, and I believe itās your products that are keeping it that way.Ā Not once have I been pulled up on the side of the road, not once!! TheĀ FTCĀ Decarbonizer,Ā Flushing Oil ConcentrateĀ andĀ ULS Diesel EnhancerĀ do a great job. I havenāt touched the injectors at all, oil pressure is strong all the time, engine runs smooth and strong, the initialĀ blowbyĀ settled down and has never come back. Thanks for great products, I really believe in them.”
Howard B. Monroe, TN
Stopped using oil
“ā¦ we got someĀ Flushing oil ConcentrateĀ a while ago because the truck was using about 1 liter of engine oil every 1000 kilometers, and at 850,000 kilometers we were sure it was going to need a rebuild. But we tried theĀ Flushing OilĀ ConcentrateĀ and things improved. Now itās only using about 2-3 liters every 20,000 kilometers. Weāre sold!”
Randy K, SK, Canada
Swear by these products
“Thanks for sending out these products. I have been using these products for 10 years in Australia, and Iāve recently moved back to Canada and absolutely swear by them. I maintain our cars and boats personally, and I can see the benefit from the reduced maintenance effort and costs these products afford.
I first got exposed to these products when we were living in Australia, and Iād bought a 2006 Jeep Grand Cherokee. It was the diesel version running the Mercedes engine and transmission. It was having a bunch of engine problems, so while I was doing all the repairs, a friend there recommended doing an engine flush withĀ Flushing Oil Concentrate. The success I had with that led to yourĀ other products, and from then Iāve purchased all the other products over the time and never looked back.
While I was in Australia I was working for a large international alumina refineryĀ and we used many of your products Ā in our fleet of D12ās, Komatsu dozers, and Komatsu FELās.
A few years ago our BMW X5 with the 3.0L gasoline engine lost all compression in the #1 cylinder due to stuck piston rings (which is a known design flaw of the CCV system dumping all the crankcase gases mostly back to this cylinder).
I dropped the oil in the car and put in a new filter along with new oil. Put in the recommended concentrated dose ofĀ Flushing Oil Concentrate, and double doses ofĀ FTC DecarbonizerĀ in the fuel.Ā I ran about 3 tanks of fuel through it this way, and the compression came back within spec in only a few weeks. It saved me a total engine tear down.
A very good friend of mine has a 2004 Honda CR-V which is havingĀ very bad blow-by issuesĀ on cylinder #4. So, Iāve talked him into trying what I did to our BMW X5 to free up the rings. Just wanted to say thanks, and to let you know I am a firm believer in these very effective, cost saving products (have been for 10 years).”
James L. BC, Canada
Products speak for themselves
“I got theĀ Engine Blowby PackĀ from you a while ago, sorry itās taken so long to get back to you, but just knew I had to let you know. Used theĀ Flushing Oil ConcentrateĀ as you told me to, so muchĀ sludge and black stuffĀ came out. Wow! After 45 minutes of running the flush, the new oil came out and looked like it was 12,000 miles old already, so full of thick sludge. Amazing! UsingĀ Flushing Oil ConcentrateĀ andĀ FTC DecarbonizerĀ reduced significantly theĀ blowby, itās got more power, more torque, and runs much smoother, I can really tell the difference. Itās like the engine just woke up, sheās now a spirited gal! So much more responsive. I could beat the drum all day, very happy with these products, theyĀ definitely speak for themselves. Just thought I should let you know.”
Will M, New Haven, CT
Better already
“I did theĀ oil flushĀ on the truck and Iāve done a round trip with theĀ FTC DecarbonizerĀ and the blowby is much better already. Iāll keep running it, it works.”
Rob C, Davenport, FL
Cummins ISB good results
“We got theĀ Blowby packĀ for the Cummins ISB 6.7 in our 2007 Kenworth box truck with only 200,000 miles. Itās an around town truck, and does not do any hard work. It had pretty bad blowby and power was right down. We did the oil flush using theĀ concentrate, and can say thatĀ the engine oil is still clean a long time after we flushed it. We think thatās quite amazing. TheĀ FTC DecarbonizerĀ seems to be doing itās work, the turbo which had never really activated for a very long time, is now activating, and the horse power is up and itās running great.Ā Blowby has completely gone.”
Aaron B. Sacramento, CA
Very impressed!
“My Cummins ISX, had around 700,000 miles on it. It had blowby, was using a lot of oil, and also DPF problems too ā lots of forced regens needed far too often.
Iād been hearing lots of good about these products, been told they are much better than other products out there. So I got theĀ Blowby PackĀ to try it out.
One month later, hereās what I can say. Iām very impressed, I am!
I did theĀ oil flushĀ soon after I got it. Ran it in the oil forĀ 45 minutes at fast idle, then drained it out. I could not believe how much sludge and other stuff came out. The oil filter was covered in sludge too. (Iād recommend putting a new filter on before doing the flush, I didnāt and mine was badly blocked with thick sludge). The oil flush obviously cleaned off years of built-up deposits.
For sh*ts and giggles, I ran new clean oil in the engine for 10 minutes after the flush, then drained it out again. More black sludge came out, probably residue left over from the flush.
We had to remove the oil pan because of another issue. Our mechanic was amazed how much was cleaned out, he said everything was as clean as a whistle in there.
On this engine,Ā the oil is normally totally blackĀ very soon after an oil change, nowĀ hundreds of miles later, the oil is still clear.
The DPF was havingĀ very frequent forced regens. I often do computer-monitored forced regens just to see whatās going on. On the first time withĀ FTC DecarbonizerĀ in the fuel, the DPF soot level went all the way to zero! Iāve never seen it go to zero before, and it did it in half the usual time, couldnāt believe what I was seeing, a great indicator of how well it works.
Since Iāve been using these products, theĀ blowby issueĀ has corrected, and theĀ oil burning problemĀ has stopped also.”
Matt T. Plymouth, NH
Large marine diesel with blowby
“I have a Detroit Series 60 Marine diesel that had a glazing problem resulting in oilĀ blowbyĀ 2100 hours after a rebuild. I grabbed theĀ Blowby PackĀ from you and started using theĀ FTC DecarbonizerĀ immediately. Soon after, I did an oil flush using theĀ Flushing Oil Concentrate. Ā Hereās the results āĀ after 25 hours of use the engine oil is still cleanĀ and has a slight grayish tint but still clean. The stern has no black soot and while running at 65% load thereās no dark cloud behind me. I believe itās saved a teardown and rebuild.”
Russ B. Boothby Harbor, ME
Series 60 Detroit oil flush
“Got theĀ Blowby PackĀ a few months ago for my 60 Series Detroit, and did the engine oilĀ flushĀ soon after. I think its incredible how much sludge and other material the flush got out. I kept a sample of the original oil, then compared it to the oil that came out 45 minutes later (the flush treated oil), and itās incredible how black it was! I couldnāt tell the difference between the 2 oil samples! 45 minutes earlier that had been new, clean oil. My mechanic was amazed at what he saw! Now,Ā a few months later, the oil is still looking good, though starting to turn darker now. But it feels clean when I rub it between my fingers. The oil pressure increased and has stayed there over the time. Itās running good. Iām happy with the overall improvement. I want to keep this truck for a while yet. TheĀ FTC DecarbonizerĀ will help that. Thanks for all your help.”
Oliver L. Windsor, ON, Canada
Old Mack tidied up
“I got theĀ Engine Blowby PackĀ about a year or so ago for my 1975 Mack. It worked pretty good. The blowby stopped and the other problems got better quickly too. For an old engine, it tidied up pretty good. One thing that stuck out was how after using theĀ oil flush concentrateĀ the engine oil stayed clean for so long. It would always be black right after I changed the oil. After the flush itĀ stayed clean for at least 800 milesĀ or more. Love this stuff, it works.”
Paul J, Bennington, NE
Sludge shock
“I just bought a 2005 Dodge Ram 3500 with the Cummins 5.9 with 211,000 miles. It had no service history, the oil looked the worst Iād ever seen, really black and gritty. I used the Flushing Oil Concentrate like you said, and I was was shocked at what came out with the flush, there was so much sludge and who knows what. The oil now is much better, but still is a little dirty, so Iām planning on doing a follow up flush in about 500 miles to get it completely cleaned up.”
J.D. LA
Kubota problems fixed
“The small Kubota had a lot of problems. It had bad blowby, oil trickled out the tube, there was white exhaust smoke when it was started cold, it was burning oil, and oil was spitting out the exhaust. I got yourĀ blowby packĀ and honestly, the results were startling. The blowby stopped, it now starts so much faster and easier, it runs so much better, the other problems have stopped too. Iām happy as a clam with these products, they really work.”
Dana H. ID
Kubota burning oil
“I had ordered the Flushing Oil Concentrate and FTC Decarbonizer earlier. I used the items on an old Kubota tractor that had 4200 hours on it and was having a lot of blow-by. It was using oil at the rate of a quart every 1 1/4 hours of use. After following the directions you sent, it continued to use oil at the same rate. I thought well there must be more major problems than just carbonized rings. However, after about 20 hours the tractor stopped using oil. It now has another 10 hours without using enough oil to even detect any usage on the dipstick. Iām very pleased with the result.”
Bob P, Gaston OR
4-cylinder gas engine
“I got theĀ engine blowby packĀ for our 2000 Dodge Caravan with the 4-cylinder gas engine. It was running rough, had lost some power, and compression was down to 65psi on at least one cylinder. Obviously I didnāt want to spend the money on replacing the engine. I did theĀ oil flushĀ and started using theĀ decarbonizerĀ in the gas tank. Iāve since driven about 2000 miles and itās running so much better. Even my mechanic says itās running really good! He did another compression test to check and the lowest cylinder is now just under 100psi. Iām really pleased so far, itās still on the road, and going very well.”
James A, North Conway, NH
ISX15 Oil consumption fixed
“My ISX 15 Cummins has around 750,000 miles, and started using a lot of oil over the past few months or so. The cost of an inframe overhaul was not good. I decided to go ahead and order your products and did theĀ oil change flushĀ about 10 days ago. Great stuff! Usually the new oil is black again right after I get the oil changed. Now, 10 days on the road, and itās still clean on the dipstick! Thatās crazy! TheĀ oil consumption has now dropped backĀ to almost nothing. TheĀ FTC DecarbonizerĀ andĀ ULS Diesel EnhancerĀ are making a huge difference too. Iām sure the rings and injectors have cleaned up. The engine is running a ton smoother, itās up on power, and miles per gallon is up too. Itās like itās opened up, got everything cleaned up. Iām noticing a real difference, itās crazy! IāmĀ very happy with the products, Iāll keep using them, keep this girl on the road. Iāve already told a lot of other drivers about them. Thanks for your help!”
Jean I, Lorain, OH
Twin Diesel Marine Cummins
“We have a recreational boat with twin 8L Cummins marine engines. Theyāre 21 years old, but only have 1780 hours total. Over the years weāve done regular oil changes and maintenance. We thought that was enough, but it seems that was the downfall. The boat sits a lot (obviously) and has a lot of long periods of low speed/low load getting it through the ship canal and locks to get to the ocean. Summer of 2021, one engine started to smoke a bit, and would run on only 5 cylinders for a few minutes after starting. Replaced the injectors hoping that would fix it. It didnāt. Last summer (2022) it got worse ā that engine was slow to start, smoked more, and started using a lot of oil. Fall of 2022, we took the boat out after servicing for a short run. It began to knock and bang HORRIBLY, so we limped home. Tested compression, the Starboard engine #1 cylinder had 0 compression. At tear down, it was blatantly obvious that the rings had carboned up and broken, then the piston slapped around and broke, destroying the piston and liner. With only 1780 hours!
We in-framed that engine, and to preserve the port engine which was smoking and getting harder to start, we have usedĀ Flushing Oil Concentrate, and are usingĀ FTC DecarbonizerĀ andĀ ULS Diesel EnhancerĀ in the fuel tanks, andĀ AW10 AntiwearĀ in the old port engine. Results so far ā the engine oil in the port engine remains very clean after theĀ flush, the starboard/rebuilt engine will get a flush after it has bedded in. After adding theĀ FTC DecarbonizerĀ to the fuel, I noticed RPM picked up immediately and the engines idled more smoothly. Last Friday (before fuel treatment), the Starboard engine (just rebuilt) turned 2515 RPM WOT and the Port turned 2435 RPM WOT. Today, after adding theĀ diesel treatment, both engines turned 2530- so we are picking up a few horsepower for sure! Iām sure theĀ AW10Ā is helping with that also! With these engines, gaining 100 RPM is not insignificant. I canāt wait to see further improvement with a little more time.”
John E, Bellevue, WA
An amazing result
“I have to say Thank you very much for how your products saved my engine. I have a Generac home generator, powered by a Kia diesel engine. It has 12,000 hours, a lot! The engine ran well enough, but theĀ blow-byĀ was SO BAD that clouds of white smoke were coming out the tube so badly it was stirring up dust and had blocked the radiator fins! The white smoke just billowed out the tube, continuously. I was able to clean out the radiator, but expected Iād have to replace the engine. But I got your products and gave them a try. The result is unbelievable! I drained the old oil, added theĀ oil flushĀ to the new oil, and added theĀ FTC DecarbonizerĀ to the fuel. I ran it for 45 minutes, drained the oil out (so black!), refilled the engine with new oil and changed the filter. I ran it then for about an hour or so. The blow-by completely stopped! I cannot believe it. From so much blow-by to stopped! An amazing difference! This has saved me the cost of an engine overhaul. I am now going to useĀ these productsĀ on my old Kubota tractor. The oil in it is a disaster ā very bad, black oil. I really canāt wait to see the results. Also, Iāll run them in my 7.3 Powerstroke. I am amazed at how quickly this worked and how effectively they worked! I told my mechanics about what happened, theyāll be in touch with you soon. I am a very happy customer. Thank you very much!”
Rob A, Brooksville, FL
Duramax just hums now
“I purchased several of your products, theĀ Flushing Oil ConcentrateĀ and theĀ FTC Decarbonizer. Iāve been very impressed with how well theyāre working and want to thank you for such a great product and good service shipping it right out. Seriously, IāveĀ never seen an engine get so cleanĀ in there, looking inside the cover I can hardly believe it. And the engine now just hums, itās doing great. Itās a Duramax thatās done 250,000 miles. Iām very impressed! Thanks!”
Al D, Fairview, UT
Quite impressive products!
“I wanted to take the opportunity to sayĀ how much of an improvement I have seen sinceĀ using your products. My 1978 Mercedes 300CD currently has in excess of 342,000 miles. I have owned this car for over 37 of its 45 year history. So naturally, I know when itās running well, and when it isnāt. TheĀ reduction of exhaust particulate and increase in engine performanceĀ is quite significant. I use Liqui-Moly engine oil with Mos2 which has a grayish appearance, otherwise I believe the dipstick would have been perfectly clear after performingĀ the flush. TypicallyĀ the engine oil is black immediately after an oil change. Thanks again for producing some quite impressive products!“
Ray F, Dover, FL
Amazed at results!
“We got an old ex-City dump truck at an auction. Itās really old, late 1980ās, but only done 60,000 miles, with the Brazil Ford 6.6 liter diesel.Ā It had bad blowbyĀ and was blowing a lot of oil out the exhaust. It fires up nice, and runs ok, but had a lot of black exhaust smoke when we revved it hard. Rebuilding the turbo fixed that some. We got theĀ blowby packĀ from you, and really quickly started to see good results. Within a few hours of driving things started clearing up. Itās now been just over a month and the oil out the exhaust pipe has now stopped, the blowby also has stopped completely. Before thisĀ it was eating a ton of oil, thatās now fixed too. TheĀ engine oil is still really clean. And hardly any black smoke when revving it hard. Weāre really impressed with the products, amazed really at the result! Your products have saved the cost of a new engine. Weāre really pleased!”
John L, Independence, KS
Even better
“Having seen the great results I got from using theĀ FTC DecarbonizerĀ andĀ CleanpowerĀ with our old Mazda 6 recently, I got theĀ Flushing Oil ConcentrateĀ andĀ AW10 AntiwearĀ from you to use when I did the oil change yesterday. The flush worked great, the oil that came out with the flush was very dark (new oil only 45 minutes earlier). After doing the flush and then adding theĀ AW10 AntiwearĀ to the new, good oil, I could immediately tell it idled much smoother and was much quieter. It has had a slight chain rattle for a while now. I canāt hear the noise at all now, itās very smooth and quiet now. Again, thanks for these great products, they work!”
Mike C, Springville, UT